An Ethernet plug fits every Ethernet jack, and that is the whole problem with Power over Ethernet (PoE). The connector looks identical whether the cable carries data alone, 24 volts, or 48 volts, and nothing on it tells you if the device on the other end was checked before the power showed up. I’ve got seven PoE drops in my house, four access points and three Echo Hubs, and I’ve not had to fry anything yet. A good deal of that was luck based on the gear I bought.
Active PoE asks before it sends power
The handshake is what protects your gear
Active PoE is what is described in the IEEE PoE standards: 802.3af, 802.3at, and 802.3bt. These are also referred to as PoE, PoE+, and PoE++ respectively. Before the power is ever sent from a PoE-compliant switch or injector, it first probes the line to check for a specific electrical signature on the other end. If that is detected, power is negotiated at a specific power level between the two devices. If it is not detected, power remains off.
In short, you can safely plug a laptop, a printer, or a game console into a PoE switch, and nothing bad will happen. My switch, a UniFi USW-Pro-24-PoE, only supports the active PoE standards, and so every single port does this.
There are three types of active PoE available, and each is limited to a maximum output power level at the port. These are 15.4W, 30W, and 90W for the three standards. But these power levels are not quite as important as the fact that the negotiation takes place. You might not give your gear as much power as it needs, but you will not hurt it by doing so.
Passive PoE sends power the moment you plug in
Fixed voltage, no questions asked
Passive PoE systems apply a fixed power voltage (typically 12V, 24V, or 48V) to the Ethernet cable, whether the device on the other end wants it or not. It is not covered by any IEEE standard, but it is cheaper to implement, and thus is used in lower cost systems like camera kits and wireless bridges or injectors that do not have a name attached to them.
Ubiquiti is even guilty of this. My two UAP-AC-PROs are 802.3af or passive PoE 48V, while the UAP-AC-LR, which is part of the same family of access points, was passive-only PoE 24V until a hardware revision in September of 2016 that brought 802.3af to it. So within the same product line, you can see three different types of PoE support! Plug a 24V-only access point into a 48V passive PoE injector, and you can fry its power input.
Voltage isn’t the only thing that differs
Mode A, Mode B, and which wires carry the power
An Ethernet cable has four twisted pairs in it, and PoE has to choose which of these pairs is used to carry power. In Mode A, the power pairs are the same as the data pairs for 10/100Mbps Ethernet: pins 1 and 2 and 3 and 6. In Mode B, power is carried on the other two pairs, pins 4 and 5 and 7 and 8. PoE++ uses all four pairs.
A PoE-compliant device must be able to accept power in either Mode A or Mode B, so this is never an issue with active PoE. With passive PoE, it is another consideration. Most passive PoE devices are Mode B only, and the cheapest passive PoE injectors use the two spare pairs to carry the power.
This means that any time you use one of those injectors, you will only get 100Mbps on the connection, because gigabit needs all four pairs for data. If you know you are buying a passive PoE device, be sure to find a passive PoE injector that is also gigabit (often stated right on the box), and always use a solid copper cable.
The wrong match costs you one of three ways
A dead device, a device that never boots, or a slow link
If you put too much voltage into a PoE device, you will likely destroy it. For example, a 48V passive PoE injector plugged into a 24V-only PoE device can burn out its power input. If you go the other way and plug a 24V passive PoE injector into an 802.3af PoE device, you probably won’t do any damage, but the device will not power on, as 24V is too low. Another issue might be a capped Ethernet connection speed of only 100Mbps.
A case in point: I have PoE-to-USB-C converters behind all my Echo Hubs, as part of my basement build. On neither the device nor its Amazon listing does it specify which kind of PoE it uses. But I know it is active because my switch only powers devices that have passed the PoE handshake.
Read the label before the cable goes in
The key thing to look for is that both ends use the same standard: 802.3af, 802.3at, or 802.3bt. If the device or injector specifies that it is passive and has a specific voltage, you need to get the correct voltage and not plug anything else into it.
If you are looking for just one injector to use for your access point or camera, get an active one. Many support both 802.3af and 802.3at PoE standards and are also Gigabit-capable. One will cost you about $25 to $30, but it will keep you from destroying any gear you plug into it.

